|
Post by Dr. Evil on Nov 17, 2012 8:41:15 GMT -4
as far as the radio setup goes for the programming. All trims stay at 0 correct? also is it down with the idle switch up and what about tail gain settings on the radio. Sorry if they seem basic simple questions but would prefer to be sure on the setups Yes on the 0 settings for all the trims. Make sure you set the radio to "90 degrees/ 1 servo" The BW will do all the settings but the radio is used for fine tunning if you will. The tail gain is still adjust by radio but something like "expo" can be done on both ends, I only use my radio for this but can be done on the BW as well.
|
|
|
Post by Dr. Evil on Nov 17, 2012 8:43:23 GMT -4
FYI....look at it this way, if you know how to setup a heli from the start with your radio then this is a piece a cake....your are basically now doing it on the BW instead.
|
|
|
Post by Dr. Evil on Nov 17, 2012 8:46:41 GMT -4
.....also.....if you've downloaded the manual from RCA, it may look alittle different than the latest update but the setup is still basically the same. Pay attention to the reversing of direction of the servos, thats what messed me up the first time.
|
|
|
Post by Dr. Evil on Nov 17, 2012 8:49:54 GMT -4
Hey Mike, I 've to go myself but will check back in later today.
|
|
|
Post by Valkman on Nov 17, 2012 11:16:51 GMT -4
I can't remember the last setup but on this one ( the newer firmware) on the first screen make sure all the throws are going 100% on the screen. If they are not adjust the endpoints on the TX, click "welcome" to let it save and go into setup again. Now the center points should be 0 on the screen and full throws should be 100%. Also make sure when you go left or push / pull the screen does the same. Don't go any more until this is right. On the "ColPit" screen you adjust the subtrim on the BW to make sure all servos are at 90 degrees at zero pitch.
|
|
|
Post by Dr. Evil on Nov 18, 2012 10:55:05 GMT -4
Mike, how are you making out with it?
|
|
|
Post by elec1800 on Nov 19, 2012 1:11:31 GMT -4
Hey bud, sorry i havent posted. Been busy at work so i havent had a chance to work on the heli. Trying to make time but i has been a lil difficult. i really do appreciate you checking in
|
|
|
Post by heliharry on Feb 2, 2013 17:18:58 GMT -4
Dr Evil .. how you doin' today ??. I have a question about this BW Gyro, I found and downloaded the manual and printed it out. But I can't find where to download the software that the gentlemen in the video is using on his laptop ??. My BW Gyro did not come with any software. A little help or direction Please, Thanks in advance.
|
|
|
Post by Dr. Evil on Feb 2, 2013 17:47:31 GMT -4
Dr Evil .. how you doin' today ??. I have a question about this BW Gyro, I found and downloaded the manual and printed it out. But I can't find where to download the software that the gentlemen in the video is using on his laptop ??. My BW Gyro did not come with any software. A little help or direction Please, Thanks in advance. Here you go The link is for a Robird which is basically the same as the BW. Go to the link and download it and follow what it tell ya....FYI, the manual may be slightly different than the program itself meaning the steps may be shuffled around a bit or the pic. may not match but it's all basically the same due to recent updates. Let us know how you make out.... www.robird.net/g31/
|
|